Products : Marine, 1/2", 3/4" and 1/4"

UP12-PV PEEK gear pump 36 l/min with check valve

Self-priming electric pumps with helical PEEK gears and integrated check valve. Nickel-plated brass body and connections. Stainless steel shaft. Main application: bilge service.

UP6/E-BR bronze gear pump with electronic pressure sensor + SCS 26 l/min

Self-priming automatic electric pump, 12/24V, with constant pressure electronic control for the transfer of diesel and oil. Bronze gears, NBR check valve, body and connections in nickeled brass, stainless steel shaft. FKM seal and NBR O-rings. Helical bronze gears guarantee constant pressure, heavy duty cycles, less noise and can operate in the absence of liquid. The pumps are supplied with a “High-Speed” setting for Diesel transfer. The integrated SCS control panel allows the switch to the “Low-Speed” mode for the transfer of oil and viscous liquids.

UP12/E-BR bronze gear pump with electronic pressure sensor + SCS 36 l/min

Self-priming automatic electric pump, 12/24V, with constant pressure electronic control for the transfer of diesel and oil. Bronze gears, NBR check valve, body and connections in nickeled brass, stainless steel shaft. FKM seal and NBR O-rings. Helical bronze gears guarantee constant pressure, heavy duty cycles, less noise and can operate in the absence of liquid. The pumps are supplied with a “High-Speed” setting for Diesel transfer. The integrated SCS control panel allows the switch to the “Low-Speed” mode for the transfer of oil and viscous liquids.

UP14/E-BR bronze gear pump with electronic pressure sensor + SCS 46 l/min

Self-priming automatic electric pump, 12/24V, with constant pressure electronic control for the transfer of diesel and oil. Bronze gears, NBR check valve, body and connections in nickeled brass, stainless steel shaft. FKM seal and NBR O-rings. Helical bronze gears guarantee constant pressure, heavy duty cycles, less noise and can operate in the absence of liquid. The pumps are supplied with a “High-Speed” setting for Diesel transfer. The integrated SCS control panel allows the switch to the “Low-Speed” mode for the transfer of oil and viscous liquids.

UP12/E-LOBR electronic pump for oils, bronze gears + SCS

Self-priming automatic electric pump, 12/24V, with constant pressure electronic control for the transfer of diesel and oil. Bronze gears, NBR check valve, body and connections in nickeled brass, stainless steel shaft. FKM seal and NBR O-rings. Helical bronze gears guarantee constant pressure, heavy duty cycles, less noise and can operate in the absence of liquid. The pumps are supplied with a “High-Speed” setting for Diesel transfer. The integrated SCS control panel allows the switch to the “Low-Speed” mode for the transfer of oil and viscous liquids.

OCP1/6 1/2'' valve

Oil change systems. The operative functions of the pump are electronically controlled by a membrane panel. The pump is equipped with 1 or 2 valves. Conceived for oil fill and drain operations. The electronic card adjusts the speed of the pump according to oil viscosity/temperature. It also increases the speed of the pump during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation.

OCP2/6 Two 1/2'' valves

Oil change systems. The operative functions of the pump are electronically controlled by a membrane panel. The pump is equipped with 1 or 2 valves. Conceived for oil fill and drain operations. The electronic card adjusts the speed of the pump according to oil viscosity/temperature. It also increases the speed of the pump during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation.

VP45A-S vane pump with on/off switch 45 l/min, brass fittings

VP45, in all its versions, is also available with brass hose fittings ¾ BSP for hose Ø mm 20.

UP14-PV PEEK gear pump 46 l/min with check valve

Self-priming electric pumps with helical PEEK gears and integrated check valve. Nickel-plated brass body and connections. Stainless steel shaft. Main application: bilge service.

UP14/OIL-AC pump for oil

Self-priming electric pumps with helical bronze gears for transferring lubricating oils and viscous liquids. Nickel-plated brass body and stainless steel shaft.

UP6/OIL-AC pump for oil

Self-priming electric pumps with helical bronze gears for transferring lubricating oils and viscous liquids. Nickel-plated brass body and stainless steel shaft.

UP6/A-AC water pressure system with 20 l tank

Water pressure systems equipped with accumulator tank. Protected by an integrated fuse. The pumps can supply up to 5 faucets at the same time and are suitable for boats up to 60 feet. Extremely compact, they are easy to be installed in the engine compartment.

DHK1 Deck Hose Kit - 15 m retractible hose+ 3/4" conn. spray gun, quick conn.

Deck hose kit with 15m/50ft retractible hose, spray gun, 3/4” connection. Nickel plated brass fittings and quick connection suitable for DQC.

OCS5/E electronic Oil Change System - 5 BSP Valves

Compact oil change electronic systems for fixed boat installations. Conceived for oil fill and drain operations for all on-board uses like generators, engines, transmissions and catwalks. Their electronic control adjusts the speed of the pump according to oil viscosity/temperature and increases its speed during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation. OCS are indicated for a perfect cleaning of all on-board areas while avoiding leaks and dispersions on the boat floor. Easy to operate and carry.

VP45/AC Vane pump 35 l/min

Self-priming vane pump for diesel refueling. 220V version. With integrated by-pass valve, aluminum body and flange, double possibility of connection. Heavy Duty.

ATX1 stainless steel accumulator tank 0,5 l with 3/8" T-nipple

Stainless steel accumulator tank for automatic pumps. Stainless steel connection. Butyl membrane for liquid foodstuff

UP12/A-V20 water pressure system + 20 l tank

Water pressure systems equipped with accumulator tank. Protected by an integrated fuse. The pumps can supply up to 5 faucets at the same time and are suitable for boats up to 60 feet. Extremely compact, they are easy to be installed in the engine compartment.

UP12/A water pressure system PEEK gears 36 l/min

Self-priming electric pumps with PEEK helical gears, equipped with in-line filter, pressure switch, check valve to be used as automatic pumps for water pressure systems on boats, mobile homes etc. Nickelplated brass body, stainless steel shaft.

VP45 Battery kit with 45 l/min vane pump

Self-priming electric vane pump with integrated by-pass valve. Aluminum body. Two options connection for 25 mm pipe. Rotor and vanes made of resin. Brush holder with EMI filter. Main applications: diesel, oil and anti-freeze refuelling. Available also with case and handle for easy transport, On/ Off switch and battery clips.

IS16 In-line filter 1/2" BSP

Transparent in-line filter with AISI 304 stainless steel net. Snap-on locking for easy inspection and cleaning.

VP45-K refuelling kit with 45 l/min vane pump

Kit for diesel refueling. Includes the vane pump with integrated by-pass valve and battery clips. Refueling gun, 2 m priming hose, 3 m delivery hose and intake filter.

VP45-S vane pump 45 l/min with integrated on/off switch

Professional range of self-priming electric 12 V and 24 V pumps for the refueling and transfer of water, oil and diesel with ON/OFF switch integrated into the water-proof cap.

UP1/AC 230V 50 Hz pump rubber impeller 30 l/min

Self-priming electric pump for transfer of fresh or salt water with flexible impeller of nitrile rubber which allows the problem-free transit of small particles. Nickel-plated brass body, shaft in stainless steel. Electric motor 0,55 kW.

AT2 accumulator tank, 5 l , white

White coated steel accumulator tank for automatic pumps. Stainless steel connection. Butyl membrane for liquid foodstuff

UP6-RK reversible pump kit 20 l/min with panel

Electronically controlled pumps for oil and diesel filling and draining operations. The touchpad electronic sensor adjusts the speed of the motor according to the liquid viscosity and temperature. Compact design. Fits in any engine room. Automatic shut-off in case of empty tank, short circuit and after 30 minutes of operation. Fittings with 1 or 2 valves available.

UP12/A-V5 water pressure system+ 5 l tank

Water pressure systems equipped with accumulator tank. Protected by an integrated fuse. The pumps can supply up to 5 faucets at the same time and are suitable for boats up to 60 feet. Extremely compact, they are easy to be installed in the engine compartment.

UP66/E-DX electronic water pressure dual pump system 66 l/min

Self-priming water pressure systems with two connected pumps with electronic control Speed motor related to the flow rate. Reduced consumption and noise. Accumulator tank is not required. Protected against overloads. Pump functions monitored by 2 led. “Empty tank” signal and shut-off device.

EV-M312 Electric Valve 1/2" - ø12

Fuel cut-off solenoid valves for inboard engine boats, which meet RINA regulations, incorporating a hand release knob to open the valve manually in case of electrical failure, complete with ogive pipe fittings for tubing of various diameters. Brass body and stainless steel fixing bracket.

OCS9/E electronic Oil Change System - 9 BSP Valves

Compact oil change electronic systems for fixed boat installations. Conceived for oil fill and drain operations for all on-board uses like generators, engines, transmissions and catwalks. Their electronic control adjusts the speed of the pump according to oil viscosity/temperature and increases its speed during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation. OCS are indicated for a perfect cleaning of all on-board areas while avoiding leaks and dispersions on the boat floor. Easy to operate and carry.

EV-MA electric valve for water, 1/4"

Electric valve for fresh water on boats. ¼” ports. Maximum pressure 5 Bar. Brass body, stainless steel internal sleeve. Man applications: wiper systems and water distribution on boats.

UP14/AC PEEK gear pump

Self-priming electric pump for transferring diesel and water. PEEK gears, pump body and connections in nickel-plated brass, shaft in stainless steel. Seals in FKM and O-ring in NBR.

AT1 accumulator tank, 2 l , white

White coated steel accumulator tank for automatic pumps. Stainless steel connection. Butyl membrane for liquid foodstuff

UP6/AC gear pump PEEK

Self-priming electric pump for transferring diesel and water. PEEK gears, pump body and connections in nickel-plated brass, shaft in stainless steel. Seal in FKM and O-ring in NBR.

OCS3/E electronic Oil Change System - 3 BSP Valves

Compact oil change electronic systems for fixed boat installations. Conceived for oil fill and drain operations for all on-board uses like generators, engines, transmissions and catwalks. Their electronic control adjusts the speed of the pump according to oil viscosity/temperature and increases its speed during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation. OCS are indicated for a perfect cleaning of all on-board areas while avoiding leaks and dispersions on the boat floor. Easy to operate and carry.

UP6/A water pressure system 26 l/min

Self-priming electric pumps with PEEK helical gears, equipped with in-line filter, pressure switch, check valve to be used as automatic pumps for water pressure systems on boats, mobile homes etc. Nickelplated brass body, stainless steel shaft.

ATX2 stainless steel accumulator tank 2 l with 1/2" T-nipple

Stainless steel accumulator tank for automatic pumps. Stainless steel connection. Butyl membrane for liquid foodstuff

UP6-PV PEEK gear pump with check valve 26 l/min

Self-priming electric pumps with helical PEEK gears and integrated check valve. Nickel-plated brass body and connections. Stainless steel shaft. Main application: bilge service.

OCS6/E electronic Oil Change System - 6 BSP Valves

Compact oil change electronic systems for fixed boat installations. Conceived for oil fill and drain operations for all on-board uses like generators, engines, transmissions and catwalks. Their electronic control adjusts the speed of the pump according to oil viscosity/temperature and increases its speed during priming. The system automatically shuts off in case of empty tank, short circuit and after 30 minutes of operation. OCS are indicated for a perfect cleaning of all on-board areas while avoiding leaks and dispersions on the boat floor. Easy to operate and carry.

VP45-N vane pump 45 l/min

Self-priming electric vane pump with integrated by-pass valve. Aluminum body. Two options connection for 25 mm hose. Rotor and vanes made of resin. Brush holder with EMI filter. Main applications: diesel, oil and anti-freeze refuelling. Available also with case and handle for easy transport, On/Off switch and battery clips.

UP6/E-DX electronic dual pump system 52 l/min

Self-priming water pressure systems with two connected pumps with electronic control Speed motor related to the flow rate. Reduced consumption and noise. Accumulator tank is not required. Protected against overloads. Pump functions monitored by 2 led. “Empty tank” signal and shut-off device.

UP12-P PEEK gear pump 36 l/min

Self-priming electric pumps with PEEK gears, complete with in-line filter. Nickel-plated brass body with stainless steel shaft. Main applications: bilge service, transfer of water.

UP12 bronze gear pump 36 l/min

Self-priming electric pumps of small dimensions with bronze gears for transferring of liquids. Pump body in nickel-plated brass and stainless steel shaft. Main applications: transfer of diesel fuel, antifreeze.

UP14 bronze gear pump 46 l/min

Self-priming electric pump of small dimension with bronze gears for transferring of liquids. Pump body in nickel-plated brass and stainless steel shaft. Main applications: transfer of diesel fuel, antifreeze.

UP14-P PEEK gear pump 46 l/min

Self-priming electric pumps with PEEK gears. Nickel-plated brass body with stainless steel shaft. Main applications: bilge service, transfer of water.

UP12/OIL gear pump for lubricating oil

Self-priming electric pumps with helical bronze gears for transferring lubricating oils and viscous liquids. Nickel-plated brass body and stainless steel shaft. Particularly suitable for draining engine sumps and for engines lubricating operations.

UP14/OIL gear pump for lubricating oil

Self-priming electric pumps with helical bronze gears for transferring lubricating oils and viscous liquids. Nickel-plated brass body and stainless steel shaft. Particularly suitable for draining engine sumps and for engines lubricating operations.

UP6-P PEEK gear pump 26 l/min

Self-priming electric pumps with PEEK gears, complete with in-line filter. Nickel-plated brass body with stainless steel shaft. Main applications: bilge service, transfer of water.

M1 compressor

Air compressor for horns

UP14/E electronic water pressure pump 46 l/min

Self-priming automatic electric pump with helical PEEK gears, integrated check valve and electronic control. Nickel-plated brass body and stainless steel shaft. Main applications: fresh water pressure systems and shower kits on boats, rubber dinghies, sailing boats and campers. PCS control panel included.

UP6 bronze Gear pump 26 l/min

\\Self-priming electric pumps of small dimensions with bronze gears for transferring of liquids. Pump body in nickel-plated brass and stainless steel shaft. Main applications: transfer of diesel fuel, antifreeze.

UP1-M pump, rubber impeller 45 l/min

Self-priming electric pump with selflubricating rubber impeller. Now available in 3 different flow rates: 25, 35 and 45 liters/minute. Fitted with water proof cable guide and internal brush holder with EMI filter. ISO 8846 and ISO 8849. Ideal for bilge and waste water on any type of boat.

UP12/E electronic water pressure system 36 l/min

Self-priming automatic electric pump with helical PEEK gears, integrated check valve and electronic control. Nickel-plated brass body and stainless steel shaft. Main applications: fresh water pressure systems and shower kits on boats, rubber dinghies, sailing boats and campers.

UP1 pump rubber impeller 35 l/min

Self-priming electric water pumps with selflubricating flexible impeller for prolonged service life and better performance. Nickelplated brass body with stainless steel shaft.

UP6/E electronic water pressure system 26 l/min

Self-priming automatic electric pump with helical PEEK gears, integrated check valve and electronic control. Nickel-plated brass body and stainless steel shaft. Main applications: fresh water pressure systems and shower kits on boats, rubber dinghies, sailing boats and campers. Available also with control panel.